[DRBD-user] drbd write performance slow, per disk 40M/s by dd command

[zf5984599]

hi, dear all:

When I use drbd, I found the write performance very slow, against testing without drbd module.

1. the environment:
-) CentOS 5.6 
-) 2.6.18 kernel
-) drbd 8.4.1
-) drbd.conf：
resource r0 
{
    protocol B;
    
    net
    { 
max-buffers  8000;
max-epoch-size 8000;
sndbuf-size 512K;
    }

    disk
    {
 al-extents 3389;
    }


    on OSS211
    {
        device /dev/drbd0;
        disk /dev/sdb1; 
        address 192.168.100.231:7788;
        meta-disk internal;
    }

    on OSS213
    {
        device /dev/drbd0;
        disk /dev/sde1;
        address 192.168.100.213:7788;
        meta-disk internal;
    }

}


2. Test scenario:
*) without drbd module,
dd to write 1G stream into one disk, which formatted to ext3:
[para]# !echo
echo 3 > /proc/sys/vm/drop_caches 
[para]# !dd
dd if=/dev/zero of=test1 bs=1M count=1000 conv=fdatasync
1000+0 records in
1000+0 records out
1048576000 bytes (1.0 GB) copied, 10.9905 seconds, 95.4 MB/s

*) with drbd module,
dd 1G stream to the disk, which is ext3 too:
[para]# cat /proc/drbd 
version: 8.4.1 (api:1/proto:86-100)
GIT-hash: 91b4c048c1a0e06777b5f65d312b38d47abaea80 build by root at OSS213, 2012-04-16 21:38:36
 0: cs:Connected ro:Primary/Secondary ds:UpToDate/UpToDate B r-----
    ns:1260036 nr:0 dw:1260036 dr:297 al:330 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:b oos:0
[para]# 
[para]# dd if=/dev/zero of=test1 bs=1M count=1000 conv=fdatasync
1000+0 records in
1000+0 records out
1048576000 bytes (1.0 GB) copied, 26.7392 seconds, 39.2 MB/s
[para]# cat /proc/drbd 
version: 8.4.1 (api:1/proto:86-100)
GIT-hash: 91b4c048c1a0e06777b5f65d312b38d47abaea80 build by root at OSS213, 2012-04-16 21:38:36
 0: cs:Connected ro:Primary/Secondary ds:UpToDate/UpToDate B r-----

All the upper test writing disk are same. From the upper result, if i use DRBD to test, the performance 
is 39 MB/s; while if i do not use, the performance is about 95M/s.

3. My question is:
-) this write performance decays so large is normal or not? 
I had read the following from the DRBD website: 
"15.1. Hardware considerations: 
....  A single, reasonably recent, SCSI or SAS disk will 
typically allow streaming writes of roughly 40MB/s to the single disk."
But this is very slow.

-）if this is not normal, how can i turn this? is the config file something not correct?

thanks a lot
BRs,
feng
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.linbit.com/pipermail/drbd-user/attachments/20120425/27054d80/attachment.htm>