Note: "permalinks" may not be as permanent as we would like,
direct links of old sources may well be a few messages off.
Wonderful news!
Cheers!
digimer
On 30/12/13 01:28 AM, Tian Zhiying wrote:
> Hi Digimer <mailto:lists at alteeve.ca>：
> Follow the steps you gave, I have successfully completed this work.
> Very very thanks.
> ------------------------------------------------------------------------
> Tian Zhiying
> *From:* Digimer <mailto:lists at alteeve.ca>
> *Date:* 2013-12-24 11:02
> *To:* tianzy1225 <mailto:tianzy1225 at thundersoft.com>; drbd-user
> <mailto:drbd-user at lists.linbit.com>
> *Subject:* Re: [DRBD-user] Instead the bad drbd server
> Happy to help. Proceed slowly and carefully. If you get stuck or are in
> doubt about something, pause and ask here. Better to be slow and safe
> with things like this. :)
> 干杯!
> On 23/12/13 09:50 PM, Tian Zhiying wrote:
> > Digimer：
> > Thanks very much. I'm going to try.
> > ------------------------------------------------------------------------
> > Tian Zhiying
> > *From:* Digimer <mailto:lists at alteeve.ca>
> > *Date:* 2013-12-24 10:37
> > *To:* tianzy1225 <mailto:tianzy1225 at thundersoft.com>; drbd-user
> > <mailto:drbd-user at lists.linbit.com>
> > *Subject:* Re: [DRBD-user] Instead the bad drbd server
> > On 23/12/13 09:24 PM, Tian Zhiying wrote:
> > > Hi
> > > Now I have a HA，the two server IP is :192.168.1.37 and
> > > 192.168.1.38，Virtual IP is 192.168.1.35, it use drbd store data, but
> > > one of the server（192.168.1.38）hardware error, I must instead it from
> > > new server(192.168.1.39), how can I config the new server's drbd?
> > > Thanks.
> > > ------------------------------------------------------------------------
> > > Tian Zhiying
> > If you setup matching sized partitions on .39, then it should be fairly
> > simple. Update .37's resource configuration to point to .39 instead of
> > .38. Then copy /etc/drbd* from .37 over to .39, Use 'drbdadm create-md
> > <res>' to setup the new DRBD resource backing device. Make sure that the
> > resources on .37 are in WFConnection state ('drbdadm attach <res>' if
> > they aren't) and then, on .39, run 'drbdadm connect <res>'.
> > If it works well, you should be able to watch /proc/drbd and see that it
> > is sync'ing from .37 (.37 should show each resource in the connection
> > state "SyncSource" and the resource(s) on .39 should be in
> > "SyncTarget"). Once the sync completes, you data is safe again.
> > If you have any specific trouble, share the details of your
> > configuration (distro/drbd/cluster stack details and versions). Config
> > files also help us understand your setup and thus offer better advice.
> > good luck!
> > PS - If you're concerned about the process, create a few VMs and
> > replicate the current state (create two VMs, set them us as you had
> > before, delete one of the VMs, create a new VM and walk through the
> > process of adding it to the previous VM). It's _always_ better to test
> > before trying anything on production systems.
> > --
> > Digimer
> > Papers and Projects: https://alteeve.ca/w/
> > What if the cure for cancer is trapped in the mind of a person without
> > access to education?
> --
> Digimer
> Papers and Projects: https://alteeve.ca/w/
> What if the cure for cancer is trapped in the mind of a person without
> access to education?
--
Digimer
Papers and Projects: https://alteeve.ca/w/
What if the cure for cancer is trapped in the mind of a person without
access to education?