Note: "permalinks" may not be as permanent as we would like,
direct links of old sources may well be a few messages off.
On Thu, Aug 11, 2011 at 06:30:36PM -0500, Zev Weiss wrote:
>
> On Aug 11, 2011, at 5:34 AM, Masashi Yamaguchi wrote:
>
> > Hello.
> >
> > no-md-flushes's default value or behavior was changed
> > on drbd-8.4 ?
You are trying this on which "platform"/kernel version?
> > I use DRBD on LVM and barriers are not supported.
> >
> > drbd-8.3.10 with "no-disk-barrier;" works
> > but drbd-8.4.0 with "no-disk-barrier;" (or "disk-barrier: no;")
> > does not work.
> >
> > Aug 11 18:39:41 XXX kernel: block drbd0: Method to ensure write
> > ordering: flush
> > ***
> > Aug 11 18:39:41 XXX kernel: block drbd0: attached to UUIDs
> > 9FA234B78651E7A6:0000000000000000:01D5349BD9ABE16B:01D4349BD9ABE16B
> > Aug 11 18:39:41 XXX kernel: block drbd0: Barriers not supported on
> > meta data device - disabling
> > Aug 11 18:39:41 XXX kernel: block drbd0: meta data update failed!
> > Aug 11 18:39:41 XXX kernel: block drbd0: disk( Consistent -> Failed )
> > Aug 11 18:39:41 XXX kernel: block drbd0: Local IO failed in
> > drbd_md_sync. Detaching...
> > Aug 11 18:39:41 XXX kernel: block drbd0: disk( Failed -> Diskless )
> >
> > drbd-8.4.0 with "no-disk-barrier; no-md-flushes;"
> > (or "disk-barrier no; md-flushes no;") works.
> > Aug 11 18:53:05 XXX kernel: block drbd0: Method to ensure write
> > ordering: flush
> > ***
> > Aug 11 18:53:05 XXX kernel: block drbd0: attached to UUIDs
> > 9FA234B78651E7A6:0000000000000000:01D5349BD9ABE16B:01D4349BD9ABE16B
> > Aug 11 18:53:05 XXX kernel: d-con r0: conn( StandAlone -> Unconnected )
> > Aug 11 18:53:05 XXX kernel: d-con r0: Starting receiver thread
> > (from drbd_w_r0 [2881])
> >
> > Is this a change of "no-md-flushes"'s behavior?
> > ("no-md-flushes" is not mentioned in ChangeLog of 8.4.0.)
> >
> > Is meta data safe on this settings ("no-disk-barrier; no-md-flushes;") ?
> >
> > Thanks.
> >
> >
> > Logs are below...<snip>
>
> Hi,
>
> I'm afraid I don't have much in the way of helpful suggestions, but I can confirm that I've been having problems with this too. Since I updated to 8.4.0, I can't do a 'drbdadm attach' on any of my resources without first disabling md-flushes -- if I leave md-flushes enabled, I get the same 'drbd_md_sync_page_io(,...s,WRITE) failed!' error you reported. After disabling md-flushes and doing an 'attach', re-enabling md-flushes works OK on the attached resources, but if it ever becomes detached I have to disable them again before I can re-attach.
>
> I spoke to some Linbit folks on the #drbd IRC channel and they said it looked like a bug, but I haven't heard anything further on it since.
>
>
> Zev
>
> _______________________________________________
> drbd-user mailing list
> drbd-user at lists.linbit.com
> http://lists.linbit.com/mailman/listinfo/drbd-user
--
: Lars Ellenberg
: LINBIT | Your Way to High Availability
: DRBD/HA support and consulting http://www.linbit.com
DRBD® and LINBIT® are registered trademarks of LINBIT, Austria.
__
please don't Cc me, but send to list -- I'm subscribed