Note: "permalinks" may not be as permanent as we would like,
direct links of old sources may well be a few messages off.
On 6/20/07, Mike Tewner <tewner at gmail.com> wrote:
> you can start by setting
> allow-two-primaries;
> in your drbd.conf file, under net{}
>
> On 6/20/07, Anuj Singh <anujhere at gmail.com> wrote:
> >
> > hi,
> > I am using drbd-8.0.3 version on redhat enterprise 4 linux.
> > my /etc/drdb.conf is
> > global { usage-count yes; }
> > common { syncer { rate 10M; } }
> > resource r0 {
> > protocol C;
> > net {
> > cram-hmac-alg sha1;
> > shared-secret "prolog";
> > }
> > on pr009.prolo.com {
> > device /dev/drbd1;
> > disk /dev/hdb10;
> > address 192.168.10.38:7789;
> > meta-disk internal;
> > }
> > on pr0005.prolo.com {
> > device /dev/drbd1;
> > disk /dev/hda6;
> > address 192.168.10.31:7789;
> > meta-disk internal;
> > }
> > }
> >
> > while making primary both the nodes, second node gives me this error
> > act_log: used:0/127 hits:0 misses:0 starving:0 dirty:0 changed:0
> > [root at pr009 scripts]# drbdadm primary r0
> > State change failed: (-1) Multiple primaries not allowed by config
> > Command 'drbdsetup /dev/drbd1 primary' terminated with exit code 11
> > how to make both nodes primary/primary simultaneously? in drbdsetup
> > man pages there is one option with -m . but i am unable to use it.
> >
> > target is to mount gfs on both nodes for cluster HA.
> > drbdsetup /dev/drbd1 primary -o
> > State change failed: (-1) Multiple primaries not allowed by config
> > Using -m option
Thank you Mike,
it is working, I mounted both patritions, able to write on both,
unmonted again and restarting service gave me splitbrain error.
most probably some other mistake i made, going threw
http://lists.linbit.com/pipermail/drbd-user/2007-June/006950.html
it is not continuously updating, my drbd.conf
global { usage-count yes; }
common { syncer { rate 10M; } }
resource r0 {
protocol C;
startup { wfc-timeout 12; degr-wfc-timeout 120; }
net {
cram-hmac-alg sha1;
shared-secret "prolog";
allow-two-primaries;
}
on pr009.prolo.com {
device /dev/drbd1;
disk /dev/hdb10;
address 192.168.10.38:7789;
meta-disk internal;
}
on pr0005.prolo.com {
device /dev/drbd1;
disk /dev/hda6;
address 192.168.10.31:7789;
meta-disk internal;
}
}
cat /proc/drbd on pr0005 (192.168.10.31)
cs:StandAlone st:Primary/Unknown ds:UpToDate/DUnknown r---
ns:0 nr:0 dw:272 dr:269 al:0 bm:4 lo:0 pe:0 ua:0 ap:0
resync: used:0/31 hits:18 misses:4 starving:0 dirty:0 changed:4
act_log: used:0/127 hits:25 misses:0 starving:0 dirty:0 changed:0
and cat /proc/drbd on pr009 (192.168.10.38)is
1: cs:WFConnection st:Primary/Unknown ds:UpToDate/DUnknown C r---
ns:0 nr:0 dw:0 dr:0 al:0 bm:0 lo:0 pe:0 ua:0 ap:0
resync: used:0/31 hits:0 misses:0 starving:0 dirty:0 changed:0
act_log: used:0/127 hits:0 misses:0 starving:0 dirty:0 changed:0
what am i missing in this configuration, I tried to restart sevice and
check if it is updating data if one node restarts.
Thanks and regards
anugunj "anuj singh"
> > drbdsetup /dev/drbd1 primary -m
> > drbdsetup: unrecognized option '-m'
> >
> > how to make it primary primary ,
> >
> > thanks and regards
> > anugunj "anuj singh"
> > _______________________________________________
> > drbd-user mailing list
> > drbd-user at lists.linbit.com
> > http://lists.linbit.com/mailman/listinfo/drbd-user
> >
>