Note: "permalinks" may not be as permanent as we would like,
direct links of old sources may well be a few messages off.
here's the drbd module path test2:~ # find /lib/modules -name "drbd*" /lib/modules/2.6.16.13-smp/block/drbd.ko /lib/modules/2.6.16.13-4-smp/block/drbd.ko /lib/modules/2.6.16.21-0.25-smp/block/drbd.ko test2:~ # find /lib/modules/`uname -r` -name "drbd*" /lib/modules/2.6.16.13-4-smp/block/drbd.ko 2.6.16.13-4-smp was the standard kernel with the installation.. i couldn't find 2.16.13-4-smp source, so i compiled drbd against 2.6.16.13's source. and yepsh.. still doesn't seem to be loaded :( On 11/29/06, Milind Dumbare <milind at linsyssoft.com> wrote: > > On Wednesday 29 November 2006 18:49, Kamran Nisar wrote: > > they are as below > > > > > > test2:~# uname -a > > Linux test2 2.6.16.13-4-smp #1 SMP Wed May 3 04:53:23 UTC 2006 i686 i686 > > i386 GNU/Linux > So you are booting through 2.6.16.13-4-smp kernel. > > > > > > > > test2:~# lsmod > > Module Size Used by > > vfat 16000 0 > > fat 51356 1 vfat > > ext3 123528 0 > > jbd 63264 1 ext3 > > parport_pc 39524 0 > > parport 37192 1 parport_pc > > nls_utf8 6016 0 > > edd 12484 0 > > af_packet 28296 0 > > iptable_filter 6912 0 > > ip_tables 16196 1 iptable_filter > > x_tables 16388 1 ip_tables > > ipv6 242272 20 > > joydev 12992 0 > > sg 35996 0 > > st 38684 0 > > sd_mod 20352 0 > > sr_mod 18596 0 > > scsi_mod 128008 4 sg,st,sd_mod,sr_mod > > button 10640 0 > > battery 13444 0 > > ac 8964 0 > > apparmor 53144 0 > > aamatch_pcre 17408 1 apparmor > > loop 19080 0 > > dm_mod 57936 0 > > i2c_viapro 11924 0 > > via686a 19208 0 > > via_agp 13440 1 > > hwmon 6916 1 via686a > > i2c_isa 8576 1 via686a > > i2c_core 24064 3 i2c_viapro,via686a,i2c_isa > > agpgart 33352 1 via_agp > > e100 37256 0 > > mii 9088 1 e100 > > shpchp 44000 0 > > pci_hotplug 28860 1 shpchp > > ide_cd 39840 0 > > cdrom 36512 2 sr_mod,ide_cd > > reiserfs 217856 2 > > raid0 11648 1 > > fan 8580 0 > > thermal 17416 0 > > processor 31208 1 thermal > > via82cxxx 12164 0 [permanent] > > ide_disk 19200 8 > > ide_core 123340 3 ide_cd,via82cxxx,ide_disk > > > Where is drbd module? its not in yet? > > > > test2:~ # ls /lib/modules/ > > 2.6.16.13-4-smp 2.6.16.13-smp 2.6.16.21-0.25-smp > does /lib/modules/2.6.16.13-4-smp have drbd.ko anywhere? > > > > test2:~/new # pwd > > /root/new > > test2:~/new # ls > > drbd-0.7.22 drbd-0.7.22.tar.gz > Have you compiled drbd-0.7.22/drbd/ with 2.6.16.13-4-smp sources? > > > > On 11/29/06, Milind Dumbare <milind at linsyssoft.com> wrote: > > > ok post following things here > > > 1. uname -a > > > 2. lsmod > > > 3. ls /lib/modules > > > 4. your drbd tarball's path. > > > > > > On Wednesday 29 November 2006 18:30, Kamran Nisar wrote: > > > > alrite, thank you all for you support :) > > > > > > > > done with that.. now i'm getting this when trying to start drbd > > > > > > > > test2:~/new/drbd-0.7.22/scripts # drbdadm up all > > > > can not open /dev/drbd0: No such device or address > > > > > > > > i created the device using mknod.. is there any speical that needs > to > > > > be done to these devices ? > > > > > > > > On 11/29/06, Milind Dumbare <milind at linsyssoft.com> wrote: > > > > > On Wednesday 29 November 2006 16:44, Kamran Nisar wrote: > > > > > > nopes. nuthing worked...same error.. > > > > > > > > > > > > there are a few things, pls take a moment and let me know if > that > > > > > > could > > > > > > > > be > > > > > > > > > > > cause of the problem > > > > > > > > > > > > my uname -r output shows version 2.6.16.13-4 , there was no > source > > > > > > code > > > > > > > > > avaiblae so i compiled aginst the source od 2.6.16.13.. would > that > > > > > > be > > > > > > > > > screwing up things ? > > > > > > > > > > Definitel, it will screw up If you insert 2.6.16.13's module into > > > > > 2.6.16.13-4. > > > > > Compile DRBD with 2.6.16.13-4 source or build bzImage for > > > > > 2.6.16.13boot into > > > > > it and then compile and install the drbd module for it > > > > > > > > > > > On 11/29/06, Leroy van Logchem <leroy.vanlogchem at wldelft.nl> > wrote: > > > > > > > Kamran Nisar wrote: > > > > > > > > test2:~ # insmod drbd.ko > > > > > > > > > > > > > > Try modprobe. Did you depmod? > -- Regards M Kamran Nisar, -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.linbit.com/pipermail/drbd-user/attachments/20061129/bd90f137/attachment.htm>