Note: "permalinks" may not be as permanent as we would like,
direct links of old sources may well be a few messages off.
could this be related ?
test1:~ # fdisk -l
Disk /dev/hda: 80.0 GB, 80026361856 bytes
255 heads, 63 sectors/track, 9729 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/hda1 1 129 1036161 83 Linux
/dev/hda2 * 130 9729 77112000 83 Linux
Disk /dev/hdc: 203.9 GB, 203928109056 bytes
255 heads, 63 sectors/track, 24792 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/hdc1 1 24792 199141708+ fd Linux raid
autodetect
Disk /dev/hdd: 203.9 GB, 203928109056 bytes
255 heads, 63 sectors/track, 24792 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/hdd1 1 24791 199133676 fd Linux raid
autodetect
Disk /dev/md0: 407.8 GB, 407833804800 bytes
2 heads, 4 sectors/track, 99568800 cylinders
Units = cylinders of 8 * 512 = 4096 bytes
Disk /dev/md0 doesn't contain a valid partition table
=-=-=
On 12/6/06, Milind Dumbare <milind at linsyssoft.com> wrote:
>
> On Wednesday 06 December 2006 17:57, Kamran Nisar wrote:
> > Hi, I am trying to set up drbd with two nodes. After setting up drbd,
> and
> > executing drbdadm up all on both the nodes , i executed "drbdadm --
> > --do-what-I-say primary all" on server1 to make it primary. It started
> an
> > initial sync, and i left it overnight to complete. when i came back in
> the
> > morning, and executed drbdadm -- connect all on server 1, it gives me
> the
> > following error
> >
> > test1:~ # drbdadm -- connect all
> > Child process does not terminate!
> > Exiting.
> >
> >
> >
> > the cat /proc/drbd on both machines is listed below
> >
> > test1:~ # cat /proc/drbd
> > version: 0.7.14 (api:77/proto:74)
> > SVN Revision: 1989 build by root at test1, 2006-11-30 11:03:07
> > 0: cs:BrokenPipe st:Secondary/Unknown ld:Inconsistent
> > ns:4568 nr:0 dw:0 dr:12676 al:0 bm:196 lo:0 pe:22 ua:2025 ap:0
> >
> >
> >
> > test2:~ # cat /proc/drbd
> > version: 0.7.18 (api:78/proto:74)
> > SVN Revision: 2186 build by lmb at chip, 2006-05-04 17:08:27
> > 0: cs:WFConnection st:Secondary/Unknown ld:Inconsistent
> > ns:0 nr:198672496 dw:198672496 dr:0 al:0 bm:12126 lo:0 pe:0 ua:0
> ap:0
> >
> >
> >
> > the config snippet is as below
> >
> >
> >
> >
> >
> >
> > resource r0 {
> >
> > #
> > protocol C;
> >
> >
> > incon-degr-cmd "halt -f";
> > startup {
> > #
> > degr-wfc-timeout 120; # 2 minutes.
> > }
> >
> > disk {
> > on-io-error detach;
> It seems this is executed to due (see below in dmesg)
> >
> >
> >
> > size 300G;
> > }
> >
> > net {
> > }
> >
> > syncer {
> > #
> > rate 100M;
> >
> > #
> > group 1;
> >
> >
> > al-extents 257;
> > }
> >
> > on test1 {
> > device /dev/drbd0;
> > disk /dev/md0;
> > address 192.168.2.61:7788;
> > meta-disk internal;
> >
> > }
> >
> > on test2 {
> > device /dev/drbd0;
> > disk /dev/md0;
> > address 192.168.2.62:7788;
> > meta-disk internal;
> > }
> > }
> >
> >
> >
> > ==--=-=-=--=-=-=
> >
> > test1:~ # dmesg | tail
> > ide: failed opcode was: unknown
> > end_request: I/O error, dev hdd, sector 198676719
> > hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> > hdd: dma_intr: error=0x40 { UncorrectableError }, LBAsect=198676735,
> > high=11, low=14127359, sector=198676727
> Seems like I/O error here.
> > ide: failed opcode was: unknown
> > end_request: I/O error, dev hdd, sector 198676727
> > hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> > hdd: dma_intr: error=0x40 { UncorrectableError }, LBAsect=198676735,
> > high=11, low=14127359, sector=198676735
> > ide: failed opcode was: unknown
> > end_request: I/O error, dev hdd, sector 198676735
> >
> >
> >
> >
> > =-=-=-=-=
>
--
Regards
M Kamran Nisar,
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.linbit.com/pipermail/drbd-user/attachments/20061206/1a9d193c/attachment.htm>