Note: "permalinks" may not be as permanent as we would like,
direct links of old sources may well be a few messages off.
I use iptraf to monitor the status of network.
i did a failover test, "cat /proc/drbd" shows no activities, the numbers
in ns,nr,dw,dr do not increase unless I execute "drbdadm invalidate
all", however, the device in secondary node is still empty even i run
drbdadm with invalidate parameter.
the attachment is my drbd.conf and drbd_config.h
thanks lot for quick replies
David Huang
-------------- next part --------------
#
# drbd.conf example
#
# parameters you _need_ to change are the hostname, device, disk,
# meta-disk, address and port in the "on <hostname> {}" sections.
#
# you ought to know about the protocol, and the various timeouts.
#
# you probably want to set the rate in the syncer sections
#
# increase timeout and maybe ping-int in net{}, if you see
# problems with "connection lost/connection established"
# (or change your setup to reduce network latency; make sure full
# duplex behaves as such; check average roundtrip times while
# network is saturated; and so on ...)
#
#
# Upgrading from DRBD-0.6.x
#
# Using the size parameter in the disk section (was disk-size) is
# no longer valid. The agreed disk size is now stored
# in DRBD's non volatile meta data files.
#
# NOTE that if you do not have some dedicated partition to use for
# the meta-data, you may use 'internal' meta-data.
#
# THIS HOWEVER WILL DESTROY THE LAST 128M
# OF THE LOWER LEVEL DEVICE.
#
# So you better make sure you shrink the filesystem by 128M FIRST!
# or by 132M just to be sure... :)
#
skip {
As you can see, you can also comment chunks of text
with a 'skip[optional nonsense]{ skipped text }' section.
This comes in handy, if you just want to comment out
some 'resource <some name> {...}' section:
just precede it with 'skip'.
The basic format of option assignment is
<option name><linear whitespace><value>;
It should be obvious from the examples below,
but if you really care to know the details:
<option name> :=
valid options in the respective scope
<value> := <num>|<string>|<choice>|...
depending on the set of allowed values
for the respective option.
<num> := [0-9]+, sometimes with an optional suffix of K,M,G
<string> := (<name>|\"([^\"\\\n]*|\\.)*\")+
<name> := [/_.A-Za-z0-9-]+
}
#
# At most ONE global section is allowed.
# It must precede any resource section.
#
# global {
# use this if you want to define more resources later
# without reloading the module.
# by default we load the module with exactly as many devices
# as configured mentioned in this file.
#
# minor-count 5;
# The user dialog counts and displays the seconds it waited so
# far. You might want to disable this if you have the console
# of your server connected to a serial terminal server with
# limited logging capacity.
# The Dialog will print the count each 'dialog-refresh' seconds,
# set it to 0 to disable redrawing completely. [ default = 1 ]
#
# dialog-refresh 5; # 5 seconds
# this is for people who set up a drbd device via the
# loopback network interface or between two VMs on the same
# box, for testing/simulating/presentation
# otherwise it could trigger a run_tasq_queue deadlock.
# I'm not sure whether this deadlock can happen with two
# nodes, but it seems at least extremely unlikely; and since
# the io_hints boost performance, keep them enabled.
#
# With linux 2.6 it no longer makes sense.
# So this option should vanish. --lge
#
# disable-io-hints;
# }
#
# this need not be r#, you may use phony resource names,
# like "resource web" or "resource mail", too
#
resource r0 {
# transfer protocol to use.
# C: write IO is reported as completed, if we know it has
# reached _both_ local and remote DISK.
# * for critical transactional data.
# B: write IO is reported as completed, if it has reached
# local DISK and remote buffer cache.
# * for most cases.
# A: write IO is reported as completed, if it has reached
# local DISK and local tcp send buffer. (see also sndbuf-size)
# * for high latency networks
#
#**********
# uhm, benchmarks have shown that C is actually better than B.
# this note shall disappear, when we are convinced that B is
# the right choice "for most cases".
# Until then, always use C unless you have a reason not to.
# --lge
#**********
#
protocol C;
# what should be done in case the cluster starts up in
# degraded mode, but knows it has inconsistent data.
incon-degr-cmd "halt -f";
startup {
# Wait for connection timeout.
# The init script blocks the boot process until the resources
# are connected.
# In case you want to limit the wait time, do it here.
#
# wfc-timeout 0;
# Wait for connection timeout if this node was a degraded cluster.
# In case a degraded cluster (= cluster with only one node left)
# is rebooted, this timeout value is used.
#
degr-wfc-timeout 120; # 2 minutes.
}
disk {
# if the lower level device reports io-error you have the choice of
# "pass_on" -> Report the io-error to the upper layers.
# Primary -> report it to the mounted file system.
# Secondary -> ignore it.
# "panic" -> The node leaves the cluster by doing a kernel panic.
# "detach" -> The node drops its backing storage device, and
# continues in disk less mode.
#
on-io-error detach;
}
net {
# this is the size of the tcp socket send buffer
# increase it _carefully_ if you want to use protocol A over a
# high latency network with reasonable write throughput.
# defaults to 2*65535; you might try even 1M, but if your kernel or
# network driver chokes on that, you have been warned.
# sndbuf-size 512k;
# timeout 60; # 6 seconds (unit = 0.1 seconds)
# connect-int 10; # 10 seconds (unit = 1 second)
# ping-int 10; # 10 seconds (unit = 1 second)
# Maximal number of requests (4K) to be allocated by DRBD.
# The minimum is hardcoded to 32 (=128 kb).
# For hight performance installations it might help if you
# increase that number. These buffers are used to hold
# datablocks while they are written to disk.
#
# max-buffers 2048;
# The highest number of data blocks between two write barriers.
# If you set this < 10 you might decrease your performance.
# max-epoch-size 2048;
# if some block send times out this many times, the peer is
# considered dead, even if it still answers ping requests.
# ko-count 4;
# if the connection to the peer is lost you have the choice of
# "reconnect" -> Try to reconnect (AKA WFConnection state)
# "stand_alone" -> Do not reconnect (AKA StandAlone state)
# "freeze_io" -> Try to reconnect but freeze all IO until
# the connection is established again.
# on-disconnect reconnect;
}
syncer {
# Limit the bandwith used by the resynchronisation process.
# default unit is KB/sec; optional suffixes K,M,G are allowed
#
rate 10M;
# All devices in one group are resynchronized parallel.
# Resychronisation of groups is serialized in ascending order.
# Put DRBD resources which are on different physical disks in one group.
# Put DRBD resources on one physical disk in different groups.
#
group 1;
# Configures the size of the active set. Each extent is 4M,
# 257 Extents ~> 1GB active set size. In case your syncer
# runs @ 10MB/sec, all resync after a primary's crash will last
# 1GB / ( 10MB/sec ) ~ 102 seconds ~ One Minute and 42 Seconds.
# BTW, the hash algorithm works best if the number of al-extents
# is prime. (To test the worst case performace use a power of 2)
al-extents 257;
}
on davidTest {
device /dev/nb0;
disk /dev/hda6;
address 192.168.10.201:7788;
meta-disk internal;
# meta-disk is either 'internal' or '/dev/ice/name [idx]'
#
# You can use a single block device to store meta-data
# of multiple DRBD's.
# E.g. use meta-disk /dev/hde6[0]; and meta-disk /dev/hde6[1];
# for two different resources. In this case the meta-disk
# would need to be at least 256 MB in size.
#
# 'internal' means, that the last 128 MB of the lower device
# are used to store the meta-data.
# You must not give an index with 'internal'.
}
on davidPrimary {
device /dev/nb0;
disk /dev/hda7;
address 192.168.10.193:7788;
meta-disk internal;
}
}
resource r3{
protocol C;
incon-degr-cmd "halt -f";
disk {
on-io-error detach;
}
startup {
wfc-timeout 0;
degr-wfc-timeout 120; # 2 minutes.
}
syncer {
rate 100M;
}
on davidTest {
device /dev/nb1;
disk /dev/hda5;
address 192.168.10.201:7791;
meta-disk internal;
}
on davidPrimary {
device /dev/nb1;
disk /dev/hda8;
address 192.168.10.193:7791;
meta-disk internal;
}
}
-------------- next part --------------
A non-text attachment was scrubbed...
Name: drbd_config.h
Type: text/x-c-header
Size: 1868 bytes
Desc: not available
URL: <http://lists.linbit.com/pipermail/drbd-user/attachments/20040720/2fcac46f/attachment.bin>